<?xml version="1.0" encoding="utf-8"?>
<!DOCTYPE eagle SYSTEM "eagle.dtd">
<eagle version="6.5.0">
<drawing>
<board>
<plain>
<wire x1="-1.4" y1="10.24125" x2="14.63" y2="10.24125" width="0" layer="20"/>
<wire x1="14.63" y1="10.24125" x2="14.63" y2="39.28" width="0" layer="20"/>
<wire x1="14.63" y1="39.28" x2="-1.4" y2="39.28" width="0" layer="20"/>
<wire x1="-1.4" y1="39.28" x2="-1.4" y2="10.24125" width="0" layer="20"/>
<hole x="6.6" y="14.8" drill="3.2"/>
<hole x="6.6" y="24.8" drill="3.2"/>
<hole x="6.6" y="34.8" drill="3.2"/>
</plain>
<libraries>
<library name="SJR_thonkiconn">
<packages>
<package name="THONKICONN">
</package>
</packages>
</library>
<library name="mb_supply">
<description>&lt;b&gt;Supply&lt;/b&gt;
&lt;ul&gt;
&lt;li&gt;input, output, ground, and power supply.  
&lt;li&gt;these are used on a schematic for placeholders and on a board for pads for off-board components like jacks.
&lt;/ul&gt;</description>
<packages>
<package name="OCTOGON">
<description>&lt;b&gt;Octogonal Pad&lt;/b&gt;
&lt;ul&gt;&lt;li&gt;drill diameter 0.7 mm&lt;/li&gt;&lt;/ul&gt;</description>
</package>
</packages>
</library>
</libraries>
<attributes>
</attributes>
<variantdefs>
</variantdefs>
<elements>
<element name="1IN1" library="SJR_thonkiconn" package="THONKICONN" value="THONKICONN"/>
<element name="1IN2" library="SJR_thonkiconn" package="THONKICONN" value="THONKICONN"/>
<element name="1IN3" library="SJR_thonkiconn" package="THONKICONN" value="THONKICONN"/>
<element name="1_SW" library="mb_supply" package="OCTOGON" value="1_SW">
<attribute name="NAME"/>
</element>
<element name="2_SW" library="mb_supply" package="OCTOGON" value="2_SW">
<attribute name="NAME"/>
</element>
<element name="3_SW" library="mb_supply" package="OCTOGON" value="3_SW">
<attribute name="NAME"/>
</element>
</elements>
<signals>
<signal name="GND">
<contactref element="1IN1" pad="P$1"/>
<contactref element="1IN2" pad="P$1"/>
<contactref element="1IN3" pad="P$1"/>
</signal>
<signal name="N$2">
<contactref element="1IN1" pad="P$3"/>
<contactref element="1IN2" pad="P$3"/>
<contactref element="1IN3" pad="P$3"/>
</signal>
<signal name="N$3">
<contactref element="1IN1" pad="P$2"/>
<contactref element="1_SW" pad="1"/>
</signal>
<signal name="N$4">
<contactref element="1IN2" pad="P$2"/>
<contactref element="2_SW" pad="1"/>
</signal>
<signal name="N$5">
<contactref element="1IN3" pad="P$2"/>
<contactref element="3_SW" pad="1"/>
</signal>
</signals>
</board>
</drawing>
</eagle>
