J.Chong
05/18-RevD
www.analog.com/first
Power
LAYER-STACK
01-16
CUT OUT THIS AREA
1. This drawing is CAD generated. No manual changes authorized after release.
2. All printed wiring boards to be manufactured in accordance with IPC-610 Class 2.
In case of conflict this drawing governs all other specifications.
3. Material, copper sheet laminate, copper clad FR4 170Tg. Interior
layers (if applicable) to be 0.5oz copper. Exterior layers to be 1oz copper finished.
Final thickness to be 0.063" (1.6mm).
4. All holes are plated through holes unless noted otherwise. Minimum plated through holes
to have 25um thick walls.
5. All finished trace widths to be +/- 20% measured at the bottom, minimum finished
spacing to be 100um.
6. All exposed copper to be finished with ENIG Solder finish over clean bare copper.
7. Drill boards using drill data, drill patterns, and drill table provided. Hole locations
shall be 0.003" (0.075mm) about true position (radial error). All finished holes to be +/-0.003" (0.075mm)
diameter unless noted otherwise. All finished vias to be +/-0.003" (0.075mm) to closed diameter.
8. Minimum annular ring to be 50um external layers and 25um internal layers (if applicable).
9. Layer to layer misalignment shall not exceed 75um (radial error) about true position.
10. Solder mask construction to be SMOBC using green LPI solder mask material. Solder mask
to be 18 ~ 50um thick after curing, both sides.
11. Solder mask misalignment shall not exceed 0.003" (0.075mm). Solder mask may overlap through hole
solder pads by 0.001" (0.025mm) maximum, but shall not overlap SMT pads.
12. Silkscreen should be applied over solder mask using a white epoxy-based ink. The silkscreen
should not overlap solder pads unless noted otherwise.
13. Dimensions shown reflect the board size after plating.
14. The circuit board manufacturer shall apply a name and date code on the bottom side
of the board in copper etch.
Sensor
Ready?
>NAME
>VALUE
<b>CONNECTOR</b><p>
series 057 contact pc board low profile headers<p>
straight
>NAME
>VALUE
<h3>SparkFun Electronics' preferred foot prints</h3>
In this library you'll find resistors, capacitors, inductors, test points, jumper pads, etc.<br><br>
We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com.
<br><br>
<b>Licensing:</b> Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/
<br><br>
You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage.
>NAME
>VALUE
>NAME
>VALUE
<h3>SparkFun Electronics' preferred foot prints</h3>
In this library you'll find discrete LEDs for illumination or indication, but no displays.<br><br>
We've spent an enormous amount of time creating and checking these footprints and parts, but it is the end user's responsibility to ensure correctness and suitablity for a given componet or application. If you enjoy using this library, please buy one of our products at www.sparkfun.com.
<br><br>
<b>Licensing:</b> Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/
<br><br>
You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage.
>NAME
>VALUE
Sym
N°
MM
Mils
Qty
Plated
1
0.46
18
3
YES
2
0.64
25
2
NOT
3
1.00
39
34
YES
4
2.60
102
4
NOT
5
3.18
125
2
NOT
<b>EAGLE Design Rules</b>
<p>
Die Standard-Design-Rules sind so gewählt, dass sie für
die meisten Anwendungen passen. Sollte ihre Platine
besondere Anforderungen haben, treffen Sie die erforderlichen
Einstellungen hier und speichern die Design Rules unter
einem neuen Namen ab.
<b>Laen's PCB Order Design Rules</b>
<p>
Please make sure your boards conform to these design rules.
Since Version 6.2.2 text objects can contain more than one line,
which will not be processed correctly with this version.